Forward Storage

I have now begun to build the forward storage, which comprises a seat over and locker under.

At this juncture it dawned on me that the inclusion of a bucket would provide a head (toilet WC) ... rather having my dear wife hanging over the side!!

The aft stowage is coming along and I keep moving back and forward to allow glue to set on one end or the other. 

Aft Lockers

I had to make knees to reinforce the gunwales, and then fixed them in place at regular intervals, on either side.

Next came the forecastle deck and the floors.

This whole area in the transom area now gets boxed in to form a locker.

Technically the locker top is a quarterdeck, a bit too grand so we will call it a locker top. 

I then cut and fitted the bulkhead that also serves as locker front

There are two lockers (under) that can be used as seats (over) and I have began to fit the longitudinal bulkheads for these.

My next move is to complete the two lockers

Forecastle and Gunwales

I have continued to build the gunwales (pronounced 'gunnels'), First came the inwale made from two pieces laminated together.

Then two one inch filler pieces, followed by the carlin which was laminated from two pieces. Altogether these six pieces form the gunwale (see picture above)

I then began work on the tiny forecastle (pronounced 'Folk sull') which I intend to be make from a half-inch marine ply ground piece, which will be planked over. I don't want the edge of the plywood exposed and so I am setting it in to lie flush with the top planks.

Starting to Look Like a Boat at Last.

Now we have domestic help I can spend more time on the Boat Build!

I had left the top of the stem uncut as I wanted it to be a mile-stone: it would go when the first deck beam went in.

I have finished the quarter-knees and transom-knee.

The Small Triangular Quarter Knee (one on either side)

Transom Knee 

Still looking scruffy, but a good sanding and epoxy resin will work wonders

Quarter Knees, Inwales and Floors

I have now cut and fitted the quarter knees, which strengthen the transom to sides. 

Here is the port quarter knee (triangular piece)

Then I fixed the after most floor with Epoxy Resin with added Fillet Fibres, which were piped though a forcing-bag, as used in icing (topping) cakes.

Aft floor glued to planks by epoxy resin fillets

Last week, I fitted one layer of the starboard inwale to the top  strake of planking (see last posting). Today, I added the second starboard layer by laminating it (gluing it) to the first layer: It would have been difficult to bend one thick inwale and so it is made from two pieces.

The two laminated layers of the laminated inwale, looking Forward, clamped to the outer planking

View of  Starboard Inwale Looking Aft

As in the first layer, I had to scarf-joint the second layer: it wasn't long enough and I had to add a smaller length joined to the longer piece.

Scarf Joint - the length of the joint is calculated by multiplying the thickness by 8. The joint above is 4 inches long as it is 0.5 inch thick 

Floors and Transom Knee

The floors are the beams upon which the deck boards lie.  They are made from Utile, an African hardwood.

I cut the floors out quite early in the build whilst I could still get the shape from the moulds (molds). In the picture below the floors are the dark pieces of wood clamped to the bottom of the moulds.

Yesterday I offered-up the floors and began finishing them off to give a snug fit to the rounded hull.

Today I cut out the Transom Knee: the triangular bracket that ties the transom to the hog

The plans call for a knee that is either cut from a solid piece of timber, or laminated Marine Ply. Accordingly I cut out 5 pieces of ply, getting their shape by using a cardboard template: the angle between the transom and hog is greater than 90 deg. 

These five pieces will be glued together to form a laminated knee, two inches thick.

Inwalls and Transom Outboard Motor Support Beam

I've had a little time today, to get on with the build. I've cut and fitted a large piece of Utile to the transom. This is basically a support for the outboard motor. I've glued and clamped it in place.

For those unfamiliar with Utile, it is an African hardwood closely related to Sapelle and African mahogany 

I then continued work on the the inwalls. They are of Douglas Fir (2" x 0.5"). The pieces I have aren't long enough to be fitted as one continuous length so I have to add a short piece and join it to the longer piece.

and so I have scarf-joint them.

Scarf Joint (Length = Thickness x  8)

The overall effect is: